Oumier Wasp Nano S RDA

MTL & DTL Vaping, Dual Coils, Two Post Deck, Squonk Compatible
Made In China
RDA Airflow Adjustable
RDA Diameter 25mm Ø
RDA Features 2 Post
RDA Posts 2 Post
Weight 27g
Height 3.0cm (1.2")
Diameter 2.5cm (1.0")


Temporarily Out Of Stock

The Oumier Wasp Nano S RDA is a Rebuildable Dripping Atomiser recommended for advanced vapers. Featuring a single/dual coil configuration on a two post Stainless Steel build deck, it can be configured for both MTL (Mouth to Lung) and DTL (Direct to Lung) vaping. The Wasp Nano S can be paired with most vape mods via its 510 connection, while its bottom-feeding pin ensures that it can also be paired with squonk mods. Thanks to its 5mm deep well, you can do a lot of vaping between dripping.


  • Dual Post Single/Dual Coil Build Deck
  • BF 510 Connection
  • 25mm Diameter with 810 drip tip
  • Stainless-Steel Construction
  • 5mm Deep E-liquid Well
  • Side Airflow Vents To Side Of Coil
  • Slotted Top Cap Airflow Control

Made of Stainless Steel, the Wasp Nano S has a sturdy construction, and is both hardwearing and easy to clean. At the same time, it is easy to take apart and assemble, thanks to the smooth machining on the threads. The deck features 4 terminals, secured from the top, to accommodate two rebuildable coils. In a somewhat unconventional design, the posts are not linear but angled in such a way that the positioning of the two coils is offset rather than parallel, leaving space for the ends of the wicks of each coil.

The Wasp Nano S features big airflow channels, and the top cap turns continuously in either direction, without stops, to increase or decrease the size of the air holes. This makes it easy for you to adjust the airflow for a wider inhale to suit DTL vaping or a narrower air intake for MTL vaping. The Wasp Nano S is compatible with most vape mods, including squonk mods, thanks to the hollow 510 squonk pin supplied, that you can use in place of the pre-installed solid 510 pin.


  • Oumier Wasp Nano S RDA
  • BF (Bottom Filling) Pin
  • 2x O-Rings
  • 2x Rebuildable Coils
  • 2x Slotted Set Screws (M2.5 x 3.5)
  • Phillips Screwdriver
  • Organic Cotton Wick
  • Flathead Screwdriver
  • Coil Jig

Important information about Rebuildable Dripping Atomisers:

Rebuildable atomisers are recommended only for experienced users. You should have the knowledge and access to the equipment that is required to set up this atomiser properly.

Before building or using an RDA you should have a thorough knowledge of battery safety, Ohm's Law and vaping in general.

Before fitting a coil onto your rebuildable atomiser ensure it is in a safe condition and registering the correct Ohmage, this testing and checking can be achieved by using a dedicated Ohmmeter. Coils should not be tested on vape devices.

Recommended for advanced vapers, the Oumier Wasp Nano S RDA can be paired with a wide range of coils for MTL and DTL vaping.
The Oumier Wasp Nano S RDA can be paired with a wide range of vape devices, offering options for both MTL and DTL vaping alike.

Compatible with a wide selection of rebuildable coils, the Wasp Nano S RDA features a two post deck.
The unique two post deck on the Wasp Nano S RDA allow it to be paired with a wide range of rebuildable coils, plus the raised design makes set-up even faster.

A dual airflow system makes adjustments very simple and you can easily switch between a tight or loose inhale.
A responsive airflow makes adjustments to your inhale easier than ever, giving you the option of a looser inhale or a tighter flow that works better for MTL vaping.
24mm Ø
4 Post

Digiflavor Drop V1.5 RDA

24mm RDA, Four-Post Deck, Dual Coils, Squonk Compatible
70% VG

70VG Nicotine Shot by Top Shot

Freebase Nicotine, 18mg Nicotine Strength, 70% VG, Shortfills, TPD

Lost Vape Grus Mod

100W Variable Output, MTL/DTL, 18650/20700/21700 Required, Multi Modes
24mm Ø
4 Post

Hellvape Dead Rabbit V2 RDA

Drop Deck, Single & Dual Coils, Adjustable Air, Squonk Compatible
25mm Ø
2 Post

Hellvape Dead Rabbit V2 RTA

2ml RTA, Drop Deck, Single/Dual Coil Builds, MTL & DTL, Top Filling
24mm Ø
4 Post

Hellvape Dead Rabbit 3 RDA

24mm RDA, Four Post Drop Deck, Dual Coil Builds, Adjustable Air

Do you have a question about this product? Why not ask our expert team.

Write a Review

Registered members earn £0.50 in loyalty points for every published product review!

5 stars (0)
4 stars (1)
3 stars (0)
2 stars (0)
1 star (0)

By Rey

Okay (22 August 2021)

Useful stepping stone for someone who wants to start out with building rda's at a low price