The Wotofo Profile is a 24mm RDA (Rebuildable Dripping Atomiser). Designed for advanced users it features a postless build deck, specially designed for mesh coils and standard wound coils.
The Stainless Steel construction makes the Profile both sturdy and hardwearing. Smooth machining makes it easy to assemble and disassemble, with the rubber O-rings ensuring a tight fit that helps reduce leaking.
The postless clamp deck has been specially designed to support mesh coils but works well with a range of prebuilt coils as well. The clamp system allows for a quick and easy coil installation, supporting single coil builds.
Designed for use with squonk devices, the Profile is prefitted with a BF (Bottom Feeding) Pin that allows eliquid to travel directly to your cotton thanks to it's position in the build deck. This RDA can also be used with standard vape mods when you install the 510 Pin that's included.
You can use the Profile for both mouth to lung or sub ohm vaping depending on what type of coil you install. The dual grid airflow is fully adjustable allowing for either a restricted or breezy airflow, further enhanced by the 810 drip tip for a cool vape.
Overall the Profile is a versatile RDA that can be used with a range of vape devices and can be configured to match your vaping style.
Important information about Rebuildable Dripping Atomisers:
This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and Ohm's law.
We don't advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an Ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.
By DB from Surrey
Got this for Christmas along with the Topside, and it's incredible. I'd recommend a few You Tube sessions before you set it up, because it could disappoint if you don't do it just right. Make sure you screw in the negative post tight before you start, and to avoid dry hits, make sure you're happy with knowing how to install the mesh and how to wick it (pancake method works best for me - you need full cotton contact with the mesh at all times). But once you're up and running, it's fantastic. I bought some OFRF mesh for it, and it vapes so smoothly at just 50 to 55 W. Clean flavour, big clouds and no dry hits.
By Neil from Cumbria
I recently got the Top Side Dual with the Drop Dead and after a couple of days got this beast. I run it with mesh and can honestly say that the vapour production and flavour are up there with the Horizon Tech Falcon.
You do need to use a lot of cotton running it with mesh! go for the 6mm Wotofo cotton.
If you want to try a mesh and prefer to build your own coils then this is the tank. It's super easy to build but be gentle with the mesh strip, they don't like being pressed on too hard.
By Miles from Newcastle
Id been vaping for years and always used tanks but wanted to take a step further and get an RDA and this one appealed a lot seen as it was so easily assembled and wow! the clouds and flavour off of this is insane!
I would recommend this to anyone out there looking to buy an RDA but doesnt really know how to build coils well or just wants a quicker and easier option while still getting the benefits of an RDA.
Also ive found that you can actually last up to 1-2 weeks without needing to change the cotton or coils, meaning you can get up to around 5 months of use from one pack of coils and cotton which costs less than £10! Its' a no brainer...
Used with a SMOK G-Priv 220w mod.
By Josh from Uk
Flavour is unreal, super easy to build and wick and the build lasts ages
By RichardH from Tyne Valley
I started vaping some 7 years ago & been through most of the kit. But I've always avoided going that final step into coil building - until now.
The Profile tempted me because of the potential to do an easy build & also the first mesh device that doesn't have dry hits.
Is it easy to build on? Pretty much I'd say & gets easier the more you do it. Of course, the mesh or wire coils are pre-built as is the cotton.
It also runs on a normal mod as you can use it with or without the squonk pin.
It works great as a dripper on a normal mod & the first thing I noticed was the vast increase in flavour compared to stock coils.
However, the massive amount of cotton it takes & the deep well in the deck make this RDA a no brainer for squonking. So, I've now bought the Dovpo Topside mod. Astonishing extra flavour & clouds & convenience with the 10ml squonk bottle. See my review on the mod.
So now I'm a convert - more flavour, more clouds, much lower coil costs. Probably more juice - but who cares!!